华南理工大学学报(自然科学版) ›› 2010, Vol. 38 ›› Issue (4): 119-124.doi: 10.3969/j.issn.1000-565X.2010.04.022

• 土木建筑工程 • 上一篇    下一篇

框架-复合剪力墙结构水平位移计算方法研究

郭猛 姚谦峰   


  1. 北京交通大学 土木建筑工程学院, 北京 100044
  • 收稿日期:2009-05-27 修回日期:2009-10-10 出版日期:2010-04-25 发布日期:2010-04-25
  • 通信作者: 郭猛(1982-),男,博士生,主要从事混凝土结构抗震设计理论及新型建筑结构体系研究. E-mail:guomeng673@163.com
  • 作者简介:郭猛(1982-),男,博士生,主要从事混凝土结构抗震设计理论及新型建筑结构体系研究.
  • 基金资助:

    国家自然科学基金资助项目(50878021); 国家“十一五”科技支撑计划项目(2006BAJ04A02-05); 北京交通大学优秀博士生创新研究基金资助项目(141071522)

Calculation Method of Horizontal Displacement of Frame-Composite Shear Wall Structure

Guo Meng  Yao Qian-feng   

  1. School of Civil Engineering,Beijing Jiaotong University,Beijing 100044,China
  • Received:2009-05-27 Revised:2009-10-10 Online:2010-04-25 Published:2010-04-25
  • Contact: 郭猛(1982-),男,博士生,主要从事混凝土结构抗震设计理论及新型建筑结构体系研究. E-mail:guomeng673@163.com
  • About author:郭猛(1982-),男,博士生,主要从事混凝土结构抗震设计理论及新型建筑结构体系研究.
  • Supported by:

    国家自然科学基金资助项目(50878021); 国家“十一五”科技支撑计划项目(2006BAJ04A02-05); 北京交通大学优秀博士生创新研究基金资助项目(141071522)

摘要: 基于框架-剪力墙的结构位移计算方法,引入密肋复合墙体的剪切变形,分别建立了框架-复合剪力墙结构在倒三角形荷载、均布荷载及顶部集中荷载作用下的水平位移微分方程,给出了水平位移的解析解,并以一12层框架-复合墙结构为例进行分析.结果表明,框架-复合墙结构的剪切变形使总水平位移显著增加,且所占总位移的比例较大,位移计算必须计入剪切变形.文中还比较了框架-复合墙结构与框剪结构在位移、刚度等主要力学性能方面的异同,发现两种结构都以弯剪变形为主,但剪切变形在两者总位移中所占的比例差别很大;复合墙是一种"变刚度、变阻尼"的受力构件,框架-复合墙结构中当层间位移角为1/250时框架处于最不利受力阶段.

关键词: 框架结构, 密肋复合墙体, 框架-复合墙结构, 水平位移, 剪切变形, 弯曲变形

Abstract:

On the basis of the displacement calculation of the frame-shear wall structure and by considering the shear deformation of the multi-ribbed composite wall,the differential equations of horizontal displacement of the frame-composite shear wall structure respectively under reverse triangle load,uniform load and top concentrated load are established,and the analytical solutions to the equations are obtained.Then,a case analysis is performed with a 12-layer frame-composite shear wall structure.It is found that the shear deformation of the structure is an important component of the total deformation,so that it should be taken into consideration in the displacement calculation of the frame-composite shear wall structure.Moreover,by comparing such mechanical properties as displacement and stiffness between the frame-composite shear wall structure and the common frame-shear wall structure,it is found that(1) shear and bending deformations are two main components of the total displacements of the two structures,and the proportion of shear deformation to the total displacement varies with the structure type;(2) the composite wall is a kind of bearing member with alterable stiffness and damping;and(3) the frame of the frame-composite shear wall structure is dangerous when the floor displacement angle reaches 1/250.

Key words: frame structure, multi-ribbed composite wall, frame-composite shear wall structure, horizontal displacement, shear deformation, bending deformation