带内流道的板翅式换热器散热特性

doi:10.12141/j.issn.1000-565x.180386

华南理工大学学报（自然科学版） ›› 2019, Vol. 47 ›› Issue (1): 120-126,144.doi: 10.12141/j.issn.1000-565x.180386

• 能源、动力与电气工程 • 上一篇下一篇

带内流道的板翅式换热器散热特性

蔡惠坤^{1， 2} 翁泽钜^{1， 2} 廖亦戴¹ 苏丽君¹

1．厦门大学航空航天学院，福建厦门 361102; 2．中国科学院理化技术研究所低温工程学重点实验室，北京 100190

收稿日期:2018-07-26 修回日期:2018-09-22 出版日期:2019-01-25 发布日期:2018-12-01
通信作者: 蔡惠坤( 1984) ，男，博士，讲师，主要从事热物理、机械设计研究． E-mail:caihuikun@xmu.edu.cn
作者简介:蔡惠坤( 1984) ，男，博士，讲师，主要从事热物理、机械设计研究．
基金资助:
福建省自然科学基金资助项目( 2018D0018) ;中国科学院低温工程学重点实验室开放课题( CＲYO201708)

Heat Dissipation Characteristics of Plate-fin Heat Exchanger with Internal Flow Channel

CAI Huikun^{1， 2} WENG Zeju^{1， 2} LIAO Yidai¹ SU Lijun¹

1． Department of Mechanical and Electronic Engineering，Xiamen University，Xiamen 361102，Fujian ，China; 2． CAS Key Laboratory of Cryogenics，Technical Institute of Physics and Chemistry，Beijing 100190，China

Received:2018-07-26 Revised:2018-09-22 Online:2019-01-25 Published:2018-12-01
Contact: 蔡惠坤( 1984) ，男，博士，讲师，主要从事热物理、机械设计研究． E-mail:caihuikun@xmu.edu.cn
About author:蔡惠坤( 1984) ，男，博士，讲师，主要从事热物理、机械设计研究．
Supported by:
Supported by the Natural Science Foundation of Fujian Province( 2018D0018)

摘要/Abstract

摘要： 针对目前对带内流道的板翅式换热器研究较少及其散热量计算误差较大等问题，基于空气、热流体及散热器三者耦合的基础，构建了带内流道的板翅式换热器散热特性的仿真分析模型以及小型风洞实验系统;结果表明，构建的仿真分析模型在空气速度为 1m/s、入口温度为25℃的冷却条件下，其散热量随热流体流量的增大而增加，直至流量为 3L/min 后趋于稳定，该模型的数值分析结果与实验结果最大偏差在5% 以内．实验验证之后，探索了换热器的散热性能与流道分级数的作用关系; 结果显示，采用 4 级结构内流道的散热器散热性能最好，温度均匀性最佳，但其内流道的最高温度仍低于热流体的入口温度22K，这表明了在仿真分析中同时考虑空气、热流体及散热器三者耦合作用的必要性．

关键词: 板翅式换热器, 内流道, 散热特性, 流道分级数, 温度均匀性

Abstract: Currently，little study has been carried out on the plate-fin heat exchanger with internal flow channel， and its heat dissipation power cannot be calculated accurately as its boundary conditions are be over-simplified． Therefore，a simulation analysis model of plate-fin heat exchanger with internal flow channel and a small wind tunnel experimental system was developed based on the interactions of cooling air，hot fluid and heat exchanger． The results show that，under the cooling conditions of 1m/s air speed and 25℃air inlet temperature，the heat dissipation power increases with mass volume of hot fluid，and will be stable after the mass volume reaches 3 L/min． The maximum deviation between the numerical analysis results and the experimental results is less than 5%． After validation，the effect of flow channel level on heat dissipation performance was investigated． The result shows that the heat exchanger with four-level internal flow channel is of best efficiency and temperature uniformity，but its highest temperature in internal flow channel is still lower than that of hot fluid inlet temperature 22 K，which demonstrates the necessity to take the interactions of cooling air，hot fluid and heat exchanger into consideration in simulation analysis．

Key words: plate-fin heat exchanger, internal flow channel, heat dissipation characteristics, flow channel level , temperature uniformity

中图分类号:

蔡惠坤翁泽钜廖亦戴苏丽君. 带内流道的板翅式换热器散热特性[J]. 华南理工大学学报（自然科学版）, 2019, 47(1): 120-126,144.

CAI Huikun WENG Zeju LIAO Yidai SU Lijun.

Heat Dissipation Characteristics of Plate-fin Heat Exchanger with Internal Flow Channel

[J]. Journal of South China University of Technology (Natural Science Edition), 2019, 47(1): 120-126,144.

[1]	王红民, 陈亚楼, 王惜慧, 等. 硅油风扇离合器的散热特性[J]. 华南理工大学学报（自然科学版）, 2020, 48(8): 115-123,129.
[2]	蔡惠坤张银亮廖亦戴何天府. 多海拔下不同散热器翅片的性能分析[J]. 华南理工大学学报（自然科学版）, 2017, 45(2): 91-98.

带内流道的板翅式换热器散热特性

Heat Dissipation Characteristics of Plate-fin Heat Exchanger with Internal Flow Channel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 2

编辑推荐

Metrics

本文评价