华南理工大学学报(自然科学版) ›› 2020, Vol. 48 ›› Issue (8): 82-90.doi: 10.12141/j.issn.1000-565X.190106

• 化学化工 • 上一篇    下一篇

湿式纸基摩擦材料的压缩回弹性能

梁云 张日盈 张春辉
  

  1. 华南理工大学 制浆造纸工程国家重点实验室,广东 广州 510640
  • 收稿日期:2019-03-21 修回日期:2020-02-21 出版日期:2020-08-25 发布日期:2020-08-01
  • 通信作者: 张春辉(1979-),男,博士,教授,主要从事纸基材料、古籍保护材料研究。 E-mail:Chunhui@scut.edu.cn
  • 作者简介:梁云(1974-),女,博士,研究员,主要从事高性能纸基复合材料研究。E-mail:liangyun@scut.edu.cn
  • 基金资助:
    国家重点研发计划项目 (2017YFB0308101)

Compression-Resilience Property of Wet Paper-Based Friction Materials

LIANG Yun ZHANG Riying ZHANG Chunhui   

  1. State Key Laboratory of Pulp and Paper Engineering,South China University of Technology,Guangzhou 510640,Guangdong,China
  • Received:2019-03-21 Revised:2020-02-21 Online:2020-08-25 Published:2020-08-01
  • Contact: 张春辉(1979-),男,博士,教授,主要从事纸基材料、古籍保护材料研究。 E-mail:Chunhui@scut.edu.cn
  • About author:梁云(1974-),女,博士,研究员,主要从事高性能纸基复合材料研究。E-mail:liangyun@scut.edu.cn
  • Supported by:
    Supported by the National Key R&D Program of China (2017YFB0308101)

摘要: 通过对原料特性和配方进行调节,探究了棉纤维打浆度、碳纤维形态、摩擦粉含量和树脂弹性模量对湿式纸基摩擦材料压缩回弹性的影响,同时设计了 4 种具有不同压缩回弹性的纸基摩擦材料,分析了压缩回弹性对湿式纸基摩擦材料摩擦磨损性能的影响。研究结果表明: 棉纤维打浆度在 20oSR 以上时,材料具有良好的尺寸稳定性; 长3mm的短切碳纤维、乙醇溶剂型高弹性模量粘结树脂可提高样品的尺寸稳定性; 摩擦粉的加入可提高材料的稳定压缩率; 压缩回弹性对摩擦磨损性能有重要的影响,当湿式纸基摩擦材料的永久形变率在 4. 0% 以下、稳定压缩率在 7. 0% 以上时,材料的摩擦磨损性能较为优异。

关键词: 摩擦材料, 棉纤维, 树脂, 压缩回弹性, 摩擦磨损性能

Abstract: The effects of beating degree of cotton fiber,carbon fiber morphology,friction powder content and resin elastic modulus on the compression-resilience property of wet paper-based friction materials were investigated by adjusting the raw material characteristics and formula. And 4 paper-based friction materials with different compres-sion-resilience property were prepared to explore the influence of compression-resilience property on the friction and wear performance. The results show that the material has good dimensional stability when the beating degree of cot-ton fiber is above 20o SR; the short carbon fiber of 3 mm and ethanol solvent type resin with high elastic modulus can improve the dimensional stability of the samples; the stable compression ratio can be improved by adding the friction powder; the compression-resilience property has significant influence on friction and wear performance. The friction and wear performance of the material is rather better when the permanent deformation rate of the wet paper-based friction material is below 4. 0% and the stable compression ratio is above 7. 0%.

Key words: friction materials, cotton fibers, resin, compression-resilience property, friction and wear perfor-mance

中图分类号: