华南理工大学学报(自然科学版) ›› 2007, Vol. 35 ›› Issue (3): 61-65,76.

• 动力与电气工程 • 上一篇    下一篇

电路容差对继电保护装置可靠性影响的分析方法

王钢1 邵其专2 李晓华1   

  1. 1.华南理工大学 电力学院,广东 广州 510640; 2. 云南电力调度中心,云南 昆明 650011
  • 收稿日期:2005-12-22 出版日期:2007-03-25 发布日期:2007-03-25
  • 通信作者: 王钢(1966-),男,教授,博士生导师,主要从事电力系统继电保护及自动化研究. E-mail:wg_scut@263.net
  • 作者简介:王钢(1966-),男,教授,博士生导师,主要从事电力系统继电保护及自动化研究.
  • 基金资助:

    国家自然科学基金资助项目( 50107004 ,50337010) ;霍英东青年教师基金资助项目(81048) ;华南理工大学自然科学基金资助项目

Method to Analyze Effect of Circuit Tolerance on Reliability of Protective Relays

Wang GangShao Qi-zhuanLi Xiao-hua1   

  1. 1. School of Electric Power , South China Univ. of Tech. , Guangzhou 510640 , Guangdong , China;2. Yunnan Electric Power Dispatching Centre , Kunming 650011 , Yunnan , China
  • Received:2005-12-22 Online:2007-03-25 Published:2007-03-25
  • Contact: 王钢(1966-),男,教授,博士生导师,主要从事电力系统继电保护及自动化研究. E-mail:wg_scut@263.net
  • About author:王钢(1966-),男,教授,博士生导师,主要从事电力系统继电保护及自动化研究.
  • Supported by:

    国家自然科学基金资助项目( 50107004 ,50337010) ;霍英东青年教师基金资助项目(81048) ;华南理工大学自然科学基金资助项目

摘要: 为了分析电路容差对继电保护苯直可靠性的影响,提出以正确响应率作为可靠性指标,以系统实际输出信号幅值是否超出标称输出信号幅值的容差范围作为系统失效的可靠性判据,并确定了可靠性指标的直信区间估计.将ÜrCAD/PSpice 软件的电路仿真功能与蒙特卡罗法相结合,基于点估计法和区间估计法求取可靠性指标及其直信区间.最后以数字保护装直的数据采样系统为算例,对其电路参数进行灵敏度分析,证实了所提出方法的正确性.

关键词: 继电保护装直, 可靠性, 电路容差, 蒙特卡罗法, 数据采样系统, 灵敏度

Abstract:

In order to analyze the effect of circuit tolerance on the reliability of protective relays , the correct re-sponse rate is presented as the reliability index , and the corresponding confidence interval is estimated. Moreover ,a reliability criterion is proposed , that is , the system fails when the practical magnitude of system output signal ex-ceeds the tolerance range of the nominal magnitude. By combining the circuit simulation function of OrCAD/PSpice
software and Monte Carlo simulation method , the reliability index and its confidence interval can be obtained via point and interval estimations. As an example , the sensitivity of the component parameters in the data acquisition system of digital protector is analyzed , the results verifying the proposed method.

Key words: protective relay, reliability, circuit tolerance, Monte Carlo method, data acquisition system, sensitivity