收稿日期: 2022-08-11
网络出版日期: 2022-10-21
基金资助
国家自然科学基金资助项目(51776077);中央引导地方科技发展资金项目(桂科ZY22096022);广东省基础与应用基础研究基金资助项目(2020B1515020040);钦州市科学研究与技术开发计划项目(202116601)
Experimental Study on Heat Transfer Performance of Separated Heat Pipe Heat Exchanger in Communication Base Station
Received date: 2022-08-11
Online published: 2022-10-21
Supported by
National Natural Science Foundation of China(51776077);the Project of Central Guidance and Local Science and Technology Development Fund(Guike ZY22096022);the Guangdong Basic and Applied Basic Research Foundation(2020B1515020040)
通讯基站面临散热不均、散热系统能耗高等问题。分离式热管换热器能替代机房内空调的使用，有效减少基站散热系统能耗。分离式热管换热器传热性能的影响因素有充液率、工质类型和风量等。为了研究不同因素对换热性能的影响，通过理论计算对比分析了理论充液率和实际充液率的差异；搭建实验平台研究了不同充液率下换热器的传热性能变化规律，不同高、中温工质下换热器性能的差异以及室内外风机功率的改变对换热器性能的影响规律。研究发现：使用工质R134a时，最小充液率理论值和实际值的误差为4.74%，换热器最优充液率范围为27.1%~47.9%，且最佳充液率为31.6%，最佳充液率下换热器当量换热系数为909 W/℃；随着充液率的提升，换热器内部相变区域先增大后减小，传热形式由气态工质显热传热为主先变为工质相变潜热传热为主，而后变成液态工质显热传热为主；高温工质不适用于该分离式热管换热器，使用高温工质时，换热器内部无明显相变区域，换热器使用的工质沸点越低，相变区域越大，换热器性能越好，其最佳充液率范围也越大；随着室内、外风机功率增大，换热器性能均先迅速提升而后提升速率减缓，但蒸发器侧由于散热条件较差，提升内风机功率对系统传热性能的提升较提升外风机功率更为显著。
甘云华 , 廖月鹏 , 袁辉 , 刘锋铭 , 李勇 . 通讯基站分离式热管换热器的传热性能实验研究[J]. 华南理工大学学报(自然科学版), 2023 , 51(6) : 109 -118 . DOI: 10.12141/j.issn.1000-565X.220499
Communication base stations are facing the problems of uneven heat dissipation and high energy consumption of the heat dissipation systems. The separated heat pipe heat exchanger can replace air-conditioning in communication base stations and effectively reduce the energy consumption of base station heat dissipation systems. The heat transfer performance of separated heat pipe heat exchanger is affected by factors such as filling ratio, working fluid type and air volume. In order to study the influence of different factors on heat transfer performance, the difference between theoretical filling ratio and the actual filling ratio was analyzed through theoretical calculation. The experimental platform was built to study the heat transfer performance of heat exchanger under different filling ratios, the difference of heat exchanger performance under different high and medium temperature working fluids, and the influence of indoor and outdoor fan power change on heat exchanger performance. The study finds that when the working fluid R134a is used, the error between the theoretical value and the actual value of the minimum filling ratio is 4.74%, the optimal filling ratio range of the heat exchanger is 27.1%~47.9%, the optimal filling ratio is 31.6%, and the equivalent heat transfer coefficient of the heat exchanger under the optimal filling ratio is 909 W/℃. With the increase of filling ratio, the phase change area inside the heat exchanger increases first and then decreases, and the heat transfer form changes from sensible heat transfer of vapor working fluid to latent heat transfer of the phase change of the working fluid, and then to sensible heat transfer of the liquid working fluid. The high temperature working fluid is not suitable for the separated heat pipe heat exchanger. When using the high temperature working fluid, there is no obvious phase change area inside the heat exchanger. The lower the boiling point of the working fluid is used, the larger the phase change area, the better the performance of heat exchanger, and the larger the range of its optimal filling ratio. With the increase of power of indoor and outdoor fans, the performance of the heat exchanger increases rapidly and then slows down. However, due to the poor heat dissipation conditions on evaporator side, the improvement of the heat transfer performance of the system by increasing the power of internal fan is more significant than that of the external fan.
| 1 | 安涛，何明宪 ．双碳目标达成与移动通信基站节能减排技术的探索［J］．移动通信，2022，46（3）：93-98，102. |
| AN Tao， HE Mingxian ．Exploration on energy conservation and emission reduction technology of mobile communication base station under double carbon target［J］．Mobile Communications，2022，46（3）：93-98，102. | |
| 2 | GAN Y H， WANG J Q， LIANG J L，et al ．Development of thermal equivalent circuit model of heat pipe-based thermal management system for a battery module with cylindrical cells［J］．Applied Thermal Engineering，2020，164（C）：114523/1-11. |
| 3 | LIANG J L， GAN Y H， LI Y，et al ．Thermal and electrochemical performance of a serially connected battery module using a heat pipe-based thermal management system under different coolant temperatures［J］Energy，2019，189（C）：116233/1-16. |
| 4 | 甘云华，王建钦，梁嘉林 ．基于热管的圆柱形电池包冷却性能分析［J］．化工学报，2018，69（5）：1964-1971. |
| GAN Yunhua， WANG Jianqin， LIANG Jialin ．Cooling performance of cylindrical battery pack based on thermal management system with heat pipe［J］．CIESC Journal，2018，69（5）：1964-1971. | |
| 5 | HE L F， TANG X W， LUO Q L，et al ．Structure optimization of a heat pipe-cooling battery thermal management system based on fuzzy grey relational analysis［J］．International Journal of Heat and Mass Transfer，2022，182：121924/1-14. |
| 6 | 甘云华，黄昭惠，梁嘉林，等 ．部分压扁热管等效导热模型特性研究［J］．华南理工大学学报（自然科学版），2021，49（10）：123-132. |
| GAN Yunhua， HUANG Zhaohui， LIANG Jialin，et al ．Research on the characteristics of conduction-based model of partially flattened heat pipe［J］．Journal of South China University of Technology （Natural Science Edition），2021，49（10）：123-132. | |
| 7 | HUANG G W， LIU W Y， LUO Y Q，et al ．A novel ultra-thin vapor chamber for heat dissipation in ultra-thin portable electronic devices［J］．Applied Thermal Engineering，2020，167（C）：114726/1-10. |
| 8 | 唐恒，汤勇，万珍平，等 ．平板铝热管微沟槽吸液芯的制备及毛细性能研究［J］．机械工程学报，2019，55（6）：186-193. |
| TANG Heng， TANG Yong， WAN Zhenping，et al ．Fabrication and capillary performance of micro-grooved wicks for aluminium flat-plate heat pipes［J］．Journal of Mechanical Engineering，2019，55（6）：186-193. | |
| 9 | BUFFONE C， COULLOUX J， ALONSO B，et al ．Capillary pressure in graphene oxide nanoporous membranes for enhanced heat transport in loop heat pipes for aeronautics［J］．Experimental Thermal and Fluid Science，2016，78：147-152. |
| 10 | 刘海潮，邵双全，张海南，等 ．回路热管微通道换热器蒸发冷却实验［J］．化工学报，2018，69（S2）：161-166. |
| LIU Haichao， SHAO Shuangquan， ZHANG Hainan， et al ．Evaporative cooling experiment of microchannel heat exchanger in loop heat pipe［J］．CIESC Journal，2018，69（S2）：161-166. | |
| 11 | 王飞，王建民，邵双全 ．数据中心冷却系统多级传热温差分析［J］．化工学报，2021，72（S1）：348-355. |
| WANG Fei， WANG Jianmin， SHAO Shuangquan ．Analysis multi-stage heat transfer process of data center cooling system from the temperature difference［J］．CIESC Journal，2021，72（S1）：348-355. | |
| 12 | 严浩，刘刚，洪旸，等 ．动力型分离式热管MATLAB稳态传热模拟［J］．建筑热能通风空调，2022，41（2）：22-25，17. |
| YAN Hao， LIU Gang， HONG Yang，et al ．Matlab steady state heat transfer simulation of dynamic separated heat pipe［J］．Building Energy & Environment，2022，41（2）：22-25，17. | |
| 13 | 佟振，李晓瑞 ．CO2分离式热管在数据中心的应用［J］．制冷学报，2021，42（1）：67-73. |
| TONG Zhen， LI Xiaorui ．Application of CO2 two-phase thermosyphon loop in data centers［J］．Journal of Refrigeration，2021，42（1）：67-73. | |
| 14 | ZHANG H N， SHI Z C， LIU K T，et al ．Experimental and numerical investigation on a CO2 loop thermosyphon for free cooling of data centers［J］．Applied Thermal Engineering，2017，111：1083-1090. |
| 15 | 刘玉清，郭佳超，李浩鹏，等 ．多角度重力型分离式热管蒸发器的压降特性研究［J］．科学技术创新，2020（12）：39-40. |
| LIU Yuqing， GUO Jiachao， LI Haopeng，et al ．Study on pressure drop characteristic of multi-angle gravity separated heat pipe evaporator［J］．Scientific and Technological Innovation，2020（12）：39-40. | |
| 16 | YAO M L， GAN Y H， LUO Q L，et al ．Experimental study on the effect of filling ratio on an R141b two-phase thermosyphon loop with a horizontal parallel tube evaporator［J］．International Journal of Refrigeration，2022，137：230-243. |
| 17 | YUE C， ZHANG Q， ZHAI Z Q，et al ．Numerical study on flow and thermal characteristics of a micro-channel separated heat pipe under various surface wettability［J］．Case Studies in Thermal Engineering，2021，28：101345/1-12. |
| 18 | DING T， CAO H W， HE Z G，et al ．Visualization experiment on boiling heat transfer and flow characteristics in separated heat pipe system［J］．Experimental Thermal and Fluid Science，2018，91：423-431. |
| 19 | 郝长生，尤占平 ．通信基站用热管换热器试验研究和节能分析［J］．暖通空调，2017，47（7）：75-79，70. |
| HAO Changsheng， YOU Zhanping ．Experimental study and energy saving analysis of heat pipe exchanger used in communication base stations［J］．Heating Ventilating & Air Conditioning，2017，47（7）：75-79，70. | |
| 20 | XIA G H， ZHUANG D W， DING G L，et al ．A quasi-three-dimensional distributed parameter model of micro-channel separated heat pipe applied for cooling telecommunication cabinets［J］．Applied Energy，2020，276：115544/1-14. |
| 21 | WANG T， LI Y H， LIU H，et al ．The energy efficiency analysis of data center cooling based on separated heat pipe［C］∥ Proceedings of International Heat Transfer Conference 16．Beijing：Begell House Inc.，2018：3647-3654. |
| 22 | 张泉，吴亚凝，凌丽，等 ．基站用微通道分离式热管换热性能实验研究［J］．湖南大学学报（自然科学版），2016，43（7）：139-145. |
| ZHANG Quan， WU Yaning， LING Li，et al ．Experimental investigation on heat transfer characteristic of micro-channel separated heat pipe in telecommunication base station［J］．Journal of Hunan University （Natural Sciences），2016，43（7）：139-145. | |
| 23 | 杨春英，宋志鹏，魏培恒 ．基站用分离式热管的研究［J］．节能技术，2016，34（2）：182-185，193. |
| YANG Chunying， SONG Zhipeng， WEI Peiheng. Separated heat pipe system in communication base station［J］．Energy Conservation Technology，2016，34（2）：182-185，193. | |
| 24 | MOFFAT R J ．Describing the uncertainties in experimental results［J］．Experimental Thermal and Fluid Science，1988，1（1）：3-17. |
| 25 | 洪光，张春辉，罗晴，等 ．常温小温差下的分离式热管换热器充液率研究［J］．节能，2011，30（1）：24-27，2. |
| HONG Guang， ZHANG Chunhui， LUO Qing，et al ．The separating heat-pipe filling rate study with the normal temperature and small temperature difference［J］．Energy Conservation，2011，30（1）：24-27，2. | |
| 26 | 张红 ．分离式热管换热器最佳工作状态的研究［J］．石油化工设备技术，1996，17（3）：13-17. |
| ZHANG Hong ．Investigation on the optimized working status of separate type heat pipe heat exchangers［J］．Petrochemical Equipment Technology，1996，17（3）：13-17. | |
| 27 | 庄骏，张红 ．热管技术及其工程应用［M］．北京：化学工业出版社，2000：67. |
/
| 〈 |
|
〉 |
地址：广州 五山 华南理工大学17号楼 邮政编码：510640
电话： 020-87111794 邮箱：journal@scut.edu.cn
